Alcatel-Lucent OS6450-24 User's Guide Page 82
- Page / 142
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Viewing PoE Power Supply Status Managing Power over Ethernet (PoE)
page 5-4 OmniSwitch 6450 Hardware Users Guide
Viewing PoE Power Supply Status
To view the current status of power supplies installed, use the show power command, as shown below:
-> show power
Slot PS Wattage Type Status Location
----+----+---------+------+-----------+----------
1 1 900 AC UP Internal
1 2 900 AC UP External
For detailed information on the show power command output, refer to the OmniSwitch 6250/6450 CLI
Reference Guide.
Configuring Power over Ethernet Parameters
Power over Ethernet Defaults
The following table lists the defaults for PoE configuration:
Understanding and Modifying the Default Settings
The sections below provide information on each of the key components within the Power over Ethernet
software. They include information on PoE-related CLI commands. For detailed information on PoE-
related commands, refer to the OmniSwitch 6250/6450 CLI Reference Guide.
Note. PoE units support different wattage power supplies. If an unsupported power supply is used, a
console message and a trap are generated.
Parameter Description Command(s) Default Value/Comments
PoE operational status lanpower start or lanpower stop Disabled
Total power available to a port lanpower power 31 Watts (802.3at)
Total PoE power available to an
entire chassis
lanpower maxpower Varies depending on chassis and
power supply type.
Power priority level for a port lanpower priority Low
Priority disconnect status lanpower priority-disconnect Enabled
- OmniSwitch 6450 Hardware 1
- Users Guide 1
- Contents 3
- About This Guide 9
- Who Should Read this Manual? 10
- What is in this Manual? 10
- What is Not in this Manual? 10
- Documentation Roadmap 11
- Related Documentation 13
- Technical Support 14
- Documentation Feedback 14
- 1 OmniSwitch 6450 Switches 15
- Chassis Configurations 16
- Security Features 17
- Availability Features 17
- Software Rollback 18
- Hot Swapping 18
- Hardware Monitoring 18
- 2 OmniSwitch 6450 19
- Chassis and Hardware 19
- Components 19
- OmniSwitch 6450-10 20
- OmniSwitch 6450-10 Rear Panel 21
- OmniSwitch 6450-P10 23
- OmniSwitch 6450-24 26
- OmniSwitch 6450-48 32
- OmniSwitch 6450-48 Rear Panel 33
- OmniSwitch 6450-P48 35
- OmniSwitch 6450-U24 38
- LED Status 41
- Expansion Modules 42
- OS6450-XNI-U2 43
- Internal Backup Power 44
- Supplies 44
- Installing Power Supplies 46
- Completed Installation 47
- Removing Power Supplies 48
- AC Power Cords 50
- Console Port 51
- Port Pinouts 52
- Overtemp Condition 53
- Dying Gasp 54
- Link OAM PDU 55
- 3 Mounting 57
- OmniSwitch 6450 Switches 57
- Airflow Recommendations 58
- Reduced Air Flow 59
- Mechanical Loading 60
- Circuit Overloading 60
- Reliable Earthing 60
- Table-Mounting Installation 60
- Slide chassis together 64
- Bracket Plate and Screws 64
- Rack-mounting Two Chassis 65
- Rack Mounting Steps 67
- Rack Mounting Power Supplies 69
- Chassis Connector 70
- Power Supply Connector 70
- AC Power Supply Connections 71
- 4 Booting 73
- Monitoring the Chassis 76
- • Ethernet Port LEDs 77
- • System Status LEDs 77
- • Combo Port Status LEDs 77
- 5 Managing Power over 79
- Ethernet (PoE) 79
- Power over Ethernet Defaults 82
- PoE Class Detection 83
- -> lanpower 1/1 power 3000 84
- -> lanpower 1 maxpower 40 84
- Setting Port Priority Levels 85
- Disabling Priority Disconnect 86
- Enabling Priority Disconnect 86
- 6 Managing 89
- OmniSwitch 6450 Stacks 89
- Swapping Expansion Modules 91
- OmniSwitch 6450-10 Mode 91
- Roles Within the Stack 92
- Using the Chassis MAC Address 95
- Using Saved Slot Information 96
- Using Switch Uptime 97
- • Saved slot number 98
- Idle Module Role 100
- Pass-Through Mode 101
- Stack Cabling 105
- Tokens available : 31 107
- Tokens used : 1 107
- Slot 1 - Primary 109
- Slot 2 - Secondary 109
- Slot 3 - Idle 109
- Slot 4 - Idle 109
- -> reload ni 3 119
- -> reload all 120
- Avoiding Split Stacks 122
- Monitoring the Stack 126
- Management Modules 127
- A Regulatory Compliance 129
- (Circuit Modules) 130
- Statement 132
- Standards Compliance 133
- FCC Class A, Part 15 134
- Canada Class A Statement 134
- CISPR22 Class A Warning 134
- Translated Safety Warnings 136
- Power Disconnection Warning 137
- Wrist Strap Warning 140
- Clase de seguridad 142
Related products and manuals for Network switches Alcatel-Lucent OS6450-24
(68 pages)© 2020, manymanuals.com. All rights reserved. | 1.324 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals